各位高手，請問誰有以下測試項目的規范或企標，有的話煩請給我分享一下不勝感激；謝謝！或郵件給我也可以907094029@qq.com

1 Static Electrical Performance Test(靜態性能測試)
1.1 Regulation, Ripple & Efficiency Measurement(電壓電流調整率﹐紋波﹐效率測試)
1.2 Start Up Input Voltage Test(起機輸入電壓測試)
1.3 Break Regulation Input Voltage Test(輸入電壓臨界點測試)
1.4 Output V-I Characteristics Curve Test(輸出電壓電流特性曲線測試)
1.5 Audible Noise Check(可聽噪音測試)
2 Transient Electrical Performance Test(瞬態性能測試)
2.1 Inrush Current Test(浪涌電流測試)
2.2 Start Up & Turn On Delay Test(起機延時測試)
2.3 Shut Down & Hold Up Time Test(關機延時測試)
2.4 Dynamic Load Response Test(動態負載響應測試)
3 Protection Circuit Test(保護電路測試)
3.1 Over Current Protection Test(過流保護測試)
3.2 Short Circuited Protection Test(短路電路保護測試)
3.3 Over Voltage Protection Test(過壓保護測試)
3.4 Over Temperature Protection Test(過溫保護測試)
4 Power Line Disturbance Test(電源干擾測試)
4.1 Missing Cycle Test(掉電測試)
4.2 Power Line Noise Test(交流電源電氣噪聲測試 EFT)
4.3 Lightning Test(雷擊測試)
4.4 Restart after Shut Down Test(關機后重新開機測試)
4.5 Input Under Voltage Test(輸入電壓不足測試)
4.6 Power On Under Inductive AC Input Test(電感性的交流輸入下開機)
5 Environmental Test(環境測試)
5.1 Low Temperature Operating Test(低溫操作測試)
5.2 High Temperature High Humidity Operating Test(高溫高濕操作測試)
5.3 High / Low Temperature Cycle Storage Test(高低溫循環測試)
5.4 High Temperature High Humidity Storage Test(高溫高濕存儲測試)
5.5 Vibration Test(振動測試)
5.6 Drop Test(跌落測試)
6 Waveform Measurement of Critical Components(主要元件的波形測試)
7 Reliability Test(可靠性測試)
7.1 Static Component Stress Analysis – Derating(靜態元件應力分析-使用率測試)
7.2 Power Transformer Saturation Check(功率火牛飽和測試)
7.2.1Waveform Measurement of Critical Components(主要元件的波形測試)
7.2.1.1 Static Overload Condition(靜態過載條件)
7.2.1.2 Transient Conditions(瞬態條件)
7.2.2 Maximum Flux Density Calculation(最大磁通密度計算Bmax)
7.2.2.1 Static Overload Condition(靜態過載條件)
7.2.2.2 Transient Conditions(瞬態條件)
7.3 E-Cap Lifetime Check(呂電容壽命測試)
7.4 Temperature Rise Measurement (溫升測試)
7.5 Power ON-OFF Test(開關機測試)
7.6 MTBF Calculation( 平均無故障時間計算/ Mean Time Between Failure Calculation)
8 Safety Test(安規測試)
8.1 Abnormal Operating Test – Open / Short(巽常操作測試-開路/短路)
8.2 No Ventilation Test(不透風測試/密封測試)
8.3 Extra Low Input Voltage Test(特低輸入電壓測試)
8.4 Extra High Input Voltage Test(特高電壓測試)
8.5 Over Load Test(過載測試)
8.6 Visual Check on Potential Safety Problem(可見的潛在安全問題檢查)
8.7 Hi-Pot Test(高壓測試)
8.8 Insulation Resistance Test(絕緣電阻測試)
8.9 Leakage Current Test(漏電流測試)
8.10 Flammability Grades of Plastic Parts and PCB(電路底版的可燃性級數可燃性檢查)
8.11 Fuse Marking(保險絲檢查)
8.12 Creepage and Clearance(空間及爬電距離)
8.13 Y-Cap Check(Y-電容檢查)
8.14 Severe Drop Test(嚴格的跌落測試(對于AC適配器))
8.15 Severe Vibration Test(嚴格的震動測試 (對于AC適配器))
8.16 On/Off Test at High Input Voltage(高壓輸入的開關機測試)
9 EMC Test(ElectroMagnetic Compatibility 電磁兼容姓測試)
9.1 Immunity to Electro Static Discharge Test(電子靜態放電測試)
9.2 EMI Check(電磁干擾測試)
10 Mechanical Check
10.1 Dimension Check
10.2 Cable Check
10.3 Label Check
10.4 Marking Check
10.5 Fastener Check